ne/sa5234 matched quad high-performance low-voltage operational amplifier product data supersedes data of 2001 aug 03 file under integrated circuits, ic11 handbook 2002 feb 22 integrated circuits
philips semiconductors product data ne/sa5234 matched quad high-performance low-voltage operational amplifier 2 2002 feb 22 853-1445 27774 description the ne/sa5234 is a matched, low voltage, high performance quad operational amplifier. among its unique input and output characteristics is the capability for both input and output rail-to-rail operation, particularly critical in low voltage applications. the output swings to less than 50 mv of both rails across the entire power supply range. the ne/sa5234 is capable of delivering 5.5 v peak-to-peak across a 600 w load and will typically draw only 700 m a per amplifier. the bandwidth is 2.5 mhz and the 1% settling time is 1.4 m s. features ? wide common-mode input voltage range: 250 mv beyond both rails ? output swing within 50 mv of both rails ? functionality to 1.8 v typical ? low current consumption: 700 m a per amplifier ? 15 ma output current capability ? unity gain bandwidth: 2.5 mhz ? slew rate: 0.8 v/ m s ? low noise: 25 nv/ hz ? electrostatic discharge protection ? short-circuit protection ? output inversion prevention pin configuration output 1 1 input 1 2 +input 1 3 v cc 4 14 output 4 13 input 4 12 +input 4 11 gnd +input 2 5 input 2 6 output 2 7 10 +input 3 9 input 3 8 output 3 n and d packages sl00568 figure 1. pin configuration. applications ? automotive electronics ? signal conditioning and sensing amplification ? portable instrumentation test and measurement medical monitors and diagnostics remote meters ? audio equipment ? security systems ? communications pagers cellular telephone lan 5 v datacom bus ? error amplifier in motor drives ? transducer buffer amplifier ordering information description temperature range order code dwg # 14-pin plastic small outline (so) package 0 c to +70 c ne5234d sot108-1 14-pin plastic dual in-line package (dip) 0 c to +70 c ne5234n sot27-1 14-pin plastic small outline (so) package 40 c to +85 c sa5234d sot108-1 14-pin plastic dual in-line package (dip) 40 c to +85 c sa5234n sot27-1
philips semiconductors product data ne/sa5234 matched quad high-performance low-voltage operational amplifier 2002 feb 22 3 absolute maximum ratings symbol parameter rating unit v cc single supply voltage 7 v esd protection voltage at any pin 5 v esd human body model 2000 v robot model 200 v v s dual supply voltage 3.5 v v dp voltage at any device pin 1 v s 0.5 v i dp current into any device pin 1 50 ma v in differential input voltage 2 0.5 v v cm common-mode input voltage (positive) v cc + 0.5 v v cm common-mode input voltage (negative) v ee 0.5 v p d power dissipation 3 500 mw t j operating junction temperature 3 +150 c v sc supply voltage allowing indefinite output short circuit to either rail 3,4 7 v t stg storage temperature range 65 to +150 c t sld lead soldering temperature (10 sec max) +230 c q ja thermal impedance 14 pin plastic dip 80 c/w 14 pin plastic so 115 c/w notes: 1. each pin is protected by esd diodes. the voltage at any pin is limited by the esd diodes. 2. the differential input of each amplifier is limited by two internal diodes, connected in parallel and opposite to each other. for more differential input range, use differential resistors in series with the input pins. 3. the maximum operating junction temperature is +150 c. at elevated temperatures, devices must be derated according to the package thermal resistance and device mounting conditions. derates above +25 c: n package at 9.5 mw/ c; d package at 6.25 mw/ c. 4. simultaneous short circuits of two or more amplifiers to the positive or negative rail can exceed the power dissipation ratin gs and cause eventual destruction of the device. 5. guaranteed by design. recommended operating conditions symbol parameter rating unit v cc single supply voltage +2 to +5.5 v v s dual supply voltage 1 to 2.75 v v cm common-mode input voltage (positive) v cc + 0.25 v v cm common-mode input voltage (negative) v ee 0.25 v t amb temperature ne5234 0 to +70 c sa5234 40 to +85 c
philips semiconductors product data ne/sa5234 matched quad high-performance low-voltage operational amplifier 2002 feb 22 4 dc electrical characteristics v cc = 2 v to 5.5 v; v ee = 0 v; t amb = 25 c; v ee < v cm < v cc ; unless otherwise stated. test conditions limits symbol parameter test conditions ne5234 sa5234 unit min typ max min typ max v cc = 5.5 v 2.8 4.0 2.8 4.0 i cc supply current v cc = 5.5 v over full temperature range 3.0 4.6 3.2 4.8 ma 0.2 4 0.2 4 v os offset voltage over full temperature range 0.4 5 0.6 5 mv d v os / d t offset voltage drift with temperature 4 4 m v/ c offset voltage difference between any am p lifiers in 0.4 3 0.4 3 d v os between any am lifiers in the same package at the same common mode level 1 over full temperature range 0.8 4 1.2 4 mv 3 20 3 30 i os offset current over full temperature range 4 30 6 60 na d i os / d t offset current drift with temperature 0.02 0.3 0.03 0.3 na/ c 1 v ee < v cm < v ee +0.5 v 200 90 200 90 i in p ut bias current 1 over full temperature range 225 100 250 150 na i b inp u t bias c u rrent 1 v ee +1 v < v cm < v cc 25 70 25 75 na over full temperature range 35 100 35 120 d i b / d t input bias current drift with temperature 0.5 0.5 na/ c v ee < v cm < v ee +0.5v 10 30 10 30 d i b input bias current difference between an y amplifier in the over full temperature range 25 50 50 70 na y same package at the same common mode level v ee +1v < v cm < v cc 5 20 5 20 na common mode level . over full temperature range 15 30 25 50 v os 6 mv v ee 0.25 v cc +0.25 v ee 0.25 v cc +0.25 v cm common-mode input range v os 6 mv over full temperature range v ee 0.1 v cc +0.1 v ee 0.1 v cc +0.1 v common-mode rejection v ee < v cm < v ee +0.5 v; v ee +1 v < v cm < v cc 80 100 90 100 cmrr j ratio, small signal over full temperature range 75 80 db common mode rejection v ee < v cm < v cc 65 90 65 100 common - mode rejection ratio, large signal over full temperature range 60 60 v ee < v cm < v cc 80 100 80 100 psrr power supply rejection ratio over full temperature range 80 90 80 90 db peak load current sink and 10 12 10 12 i l peak load c u rrent , sink and source over full temperature range 5 8 5 8 ma
philips semiconductors product data ne/sa5234 matched quad high-performance low-voltage operational amplifier 2002 feb 22 5 dc electrical characteristics (continued) test conditions limits symbol parameter test conditions ne5234 sa5234 unit min typ max min typ max 90 110 90 110 a vol open-loop voltage gain over full temperature range 90 90 db i peak = 0.1 ma v ee +0.05 v cc 0.05 v ee +0.1 v cc 0.1 out p ut voltage swing i peak = 10 ma v ee +0.25 v cc 0.25 v ee +0.25 v cc 0.25 v v out out ut voltage swing i peak = 5 ma over full temperature range v ee +0.22 v cc 0.2 v ee +0.2 v cc 0.2 v output voltage swing for r l = 2 k w v ee +0.2 v cc 0.2 v ee +0.2 v cc 0.2 v gg v cc = 2.75 v; v ee = 2.75 v r l = 600 w v ee +0.25 v cc 0.25 v ee +0.25 v cc 0.25 v note: 1. these parameters are measured for v ee < v cm < v ee +0.5 v and for v ee +1 v < v cm < v cc . by design these parameters are intermediate for common mode ranges between the measured regions. ac electrical characteristics t amb = +25 c; v cc = 2 v to 5.5 v; r l = 10 k w ; c l = 100 pf; unless otherwise stated. limits symbol parameter test conditions ne5234 sa/se5234 units min typ max min typ max sr slew rate over full temperature range 0.5 0.8 0.5 0.8 v/ m s bw unity gain bandwidth: 3 db over full temperature range 2 2.5 4.0 2 2.5 4.0 mhz q m phase margin c l = 50 pf 55 55 deg t s 1% settling time a v = 1, 1 v step 1.4 1.4 m s v n input referred voltage noise a v = 1; r s = 0 w , at 1 khz 25 25 nv/hz 1/2 thd total harmonic distortion 10 khz, 1 v p-p , a v = 1 0.1 0.1 % output inversion prevention v in v out v cc + 5 v conventional op amp philips ne5234 t t v cc v out v out v in v in v gnd v gnd v gnd v cc 5 v sl00569 47 k w 47 k w figure 2. output inversion prevention.
philips semiconductors product data ne/sa5234 matched quad high-performance low-voltage operational amplifier 2002 feb 22 6 so14: plastic small outline package; 14 leads; body width 3.9 mm sot108-1
philips semiconductors product data ne/sa5234 matched quad high-performance low-voltage operational amplifier 2002 feb 22 7 dip14: plastic dual in-line package; 14 leads (300 mil) sot27-1
philips semiconductors product data ne/sa5234 matched quad high-performance low-voltage operational amplifier 2002 feb 22 8 definitions short-form specification e the data in a short-form specification is extracted from a full data sheet with the same type number and title. for detailed information see the relevant data sheet or data handbook. limiting values definition e limiting values given are in accordance with the absolute maximum rating system (iec 60134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the dev ice at these or at any other conditions above those given in the characteristics sections of the specification is not implied. exposure to limi ting values for extended periods may affect device reliability. application information e applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. disclaimers life support e these products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. philips semiconductors customers using or selling these products for use i n such applications do so at their own risk and agree to fully indemnify philips semiconductors for any damages resulting from such application. right to make changes e philips semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. philips semiconductors ass umes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or m ask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right in fringement, unless otherwise specified. contact information for additional information please visit http://www.semiconductors.philips.com . fax: +31 40 27 24825 for sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com . ? koninklijke philips electronics n.v. 2002 all rights reserved. printed in u.s.a. date of release: 03-02 document order number: 9397 750 09514
data sheet status [1] objective data preliminary data product data product status [2] development qualification production definitions this data sheet contains data from the objective specification for product development. philips semiconductors reserves the right to change the specification in any manner without notice. this data sheet contains data from the preliminary specification. supplementary data will be published at a later date. philips semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. this data sheet contains data from the product specification. philips semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. changes will be communicated according to the customer product/process change notification (cpcn) procedure snw-sq-650a. data sheet status [1] please consult the most recently issued data sheet before initiating or completing a design. [2] the product status of the device(s) described in this data sheet may have changed since this data sheet was published. the l atest information is available on the internet at url http://www.semiconductors.philips.com.
|
